Searching for a La Crosse Garage Door Specialist? Call 608-783-6080

How to use and program your CodeDodger® OKP-BX Keypad

acc-owkdbbx-large

Video Instructions

Programming Your Garage Door Opener KeyPad

Important! Please Read. Before you begin, be aware of the following:

  • For convenience, program your keypad before mounting.
  • If programming your garage door opener is disrupted at any point due to program failure, clear/reset your keypad. Then, start over.
  • Locate the “Learn Code” button and the “Learn Code” red LED indicator.
Create Your Wireless Keypad PIN (Personal Identification Number)

On your wireless keypad:

  • Press in order 3, 5, 7
  • Press the PROGRAM key
  • Enter your PIN (3 to 8 characters)
  • Press the PROGRAM key again.
  • Close keypad cover and wait 30 seconds
Program Keypad for One Garage Door (CodeDodger® 2)

On your wireless keypad:

  1. Press and hold the PROGRAM button until both LED lights turn BLUE
  2. Release button. Only the round LED will remain BLUE.
  3. Press and hold the PROGRAM button again then release. The Long LED will blink PURPLE
  4. Enter your PIN number using the keys on the keypad
  5. Press the UP/DOWN button. LEDs will stay on solid.
  6. Press the UP/DOWN button again. LEDs will turn off.
  7. Press any key to stop opener. (It will automatically stop at the fully open or fully closed position.)
  8. The keypad backlight will turn off in approximately 30 seconds.

NOTE: If the door does not move, check the LED on the keypad. If the LED is blinking rapidly, the PIN was entered incorrectly. After the LED stops blinking, re-enter your PIN ad try again. Any keypad button will control the door for 30 seconds after the door starts moving. Rapid blinking of the red LED indicates an error. After a few seconds the LED will turn off. Start over.

Program Keypad for Multiple Garage Doors (CodeDodger® 2)

Note: All garage door openers will use the same PIN.

On your wireless keypad:

  1. Enter your PIN and press the PROGRAM button.
  2. Press the PROGRAM button again.
  3. Press the number of doors you wish to control (2 or 3)

On your garage door opener power head:

  1. Select first opener and press and hold the PROGRAM/SET button until both LED lights turn BLUE.
  2. Release the button. Only the round LED will be BLUE.
  3. Press the UP/DOWN button again. LEDs will turn off.
  4. Press any key to stop opener. (It will automatically stop at the fully open or fully closed position.)
  5. The keypad backlight will turn off in approximately 30 seconds.

NOTE: If the door does not move, check the LED on the keypad. If the LED is blinking rapidly, the PIN was entered incorrectly. After the LED stops blinking, re-enter your PIN ad try again. Any keypad button will control the door for 30 seconds after the door starts moving. Rapid blinking of the red LED indicates an error. After a few seconds the LED will turn off. Start over.

Mounting Instructions

The keypad must be mounted in sight of the door(s), at least 5 feet above the ground and clear of any moving door parts.

Note: Mounting screws are located inside the battery compartment.

  • Remove battery cover and batteries
  • Drill a 1/16″ pilot hold for the tip mounting screw.
  • Install a screw into the drilled hole, leaving a 1/8″ gap between the screw head and the wall.
  • Hook the keypad over the screw.
  • Mark and drill pilot hole and fasten bottom screw.
  • Install batteries and cover.

Additional Assistance

Should you need additional information about installing or programming your garage door opener or remote, please call Overhead Door 7 Rivers Region at (608) 783-6080.

“We’re a ‘people first’ company, and we would welcome the opportunity to prove it to you."

Hours: Monday - Thursday: 7:30am - 4:30pm & Friday: 7:30am to 3:30pm

Get Started...

Call (608) 783-6080Send Us A Message